Features:
Socket 478 for Intel® Pentium® 4/ Celeron® processor up to 2.6GHz+ with 400MHz FSB
Intel® 845 Chipset
Max. 3GB SDRAM memory in 3 DIMM slots
ATI Rage 128 Pro AGP 4X(1.5V) VGA controller with 16MB memory
Intel® 82540EM(PLC) PHY 10/100Mbps fast Ethernet
RS232 x2/ USB port x2
Specification
System Architecture
Full size SBC with PCI/ISA Golden finger
Socket 478 Intel® Pentium® 4 processor with system bus at 400MHz
AGP 2.0 compliant
PCI V2.0 compliant
PICMG 1.0 (Rev. 2.0) compliant
CPU Support
Intel® Pentium® 4 processor with 256K cache on die
Socket 478 CPU running 400MHz system bus, CPU speed up to 2GHz or above
Main Memory
168-pin DIMM x3 Support Max. memory size to 3GB (Ready for PEAK 710VL-3G)
ECC support (single bit error correction/Multiple bit errors reporting)
No Registered DIMM Support
BIOS
Award System BIOS
Plug & Play support
Advanced Power Management support
Advanced configuration & Power Interface support
4M bits flash ROM
Chip Set
Intel® 845 Chipset
Intel® 82801 x1
I/O Controller Hub (ICH2)
Intel® 82802 x1
Firmware Hub (FWH) PCI V2.2 compliant
On Board VGA
ATI Rage 128 Pro (Ultra 4XL) VGA Controller, 1.5V AGP 4X interface
16MB VGA Memory on board
Fully PC98 and PC99 Compliant
15 pin CRT controller x1, 20 pin DVI connector x1
On Board LAN
ICH2 embedded MAC with Intel® 82562EM(PLC) (PRO/100 VM Network Connection) PHY 10/100 Ethernet controller
single Chip 10/100 Base T/TX x 1 support, full duplex
Compliant with IEEE 802.3X
Drivers support: DOS/Windows®, Windows® 95/98/2000, Windows® NT, Netware 5.0, SCO Open Server 5.0, Linux
RJ45 with LED connector x1
Support Remote Monitoring (Alerting on LAN)
On Board I/O (ICH2)
ITE 8712F-A Server I/O
SIO x2, with 2 x 16C550 UARTs, 10 pin header x1, D-Sub 9 pin x1
PIO x1, bi-directional, EPP/ECP support, 26 pin connector x1
Floppy Disk controller: 34 pin connector x1
6 pin mini DIN connector x1, for PS/2 keyboard/mouse, 5 pin connector x1 (for external keyboard)
On board buzzer x1
GPIO (4 in 4 out)
On board 2 pin header for I2C
On Board 2 pin header for reset SW / 2 pin for IDE active LED / 2 pin ATX power SW
One 3 pins power header for 3 pins Power Cable connect to Backplane Board to support ATX Power On function
On board 4 pin Additional Power Source Input
System Monitor
Derived from Super IO ITE 8712F-A to system monitor
8 voltages (For +1.8v, +3.3V, +5V, -5V, +12V, -12V, Vcore and Vcc5V Stand-By)
One Fan speed (For CPU), Two for System Fan
3 temperatures (one for CPU, the others for system)
ACPI Function
Soft Power off
Power On LAN
Power On Keyboard
Power On Ring
Real Time Clock
On chip RTC with battery back up
External Li Battery x1
Watchdog Timer
Watchdog timeout can be programmable by Software from 1~64 seconds
On Board Bus Expansion
On Board NEXCOM proprietary 32bit PCI interface for NEXCOM EBK Upgrade Module
PCI to ISA Bridge & ISAMAX Support
ITE 8888F x1 PCI to ISA Bridge
Provide 64mA high driving capability to maximize ISA signals for support ISA cards up to 20 on the backplane ISA Slot
Dimensions
338.58mm(L) x 122mm(W)
Power Requirements
+5V: 10A (Max.) +12V: 10A (Max.) -12V: 50mA (Max.)
Environments
Operating temperatures: 0°C to 60°C Storage temperatures: -20°C to 80°C Relative humidity: 10% to 90% (Non-condensing)
Certification
CE approval FCC Class A |
