Industrial communication

Distributed Motionnet Single-axis Motion Control Module with e-CON Mini-Clamp connector for Mitsubishi MELSERVO-J3/J4

• Maximum communication speed: 20 Mbps
• Pulse Output Rate: 6.6 MHz (Max.)
• Control up to 64 axes per line
• Multi-axis linear interpolation function
• 2-axis circular interpolation function
• T/S-curve acceleration and deceleration
• Change speed and position on the fly
• Slow down sensor, home sensor, positive and negative limit sensors for each axis
• Software limit and compare trigger output
• Three-way isolation for power, communication and I/O.(Provide better noise immunity and device protection)
• The EC module equipped with Mini-Clamp connector provide for an easier and debris-free wire termination process

Distributed Motionnet 8-ch Analog Input Module

• 8 +/- 10 V analog input
• RJ-45 communication port
• 2 way isolation on power, communication
• 16-bit high resolution, 0.3mV min
• High precision and low shift reference 5V inside
• Hardware offset, gain calibration to EEPROM storage
• Rapid A/D transformation. Sampling rate = 250 ksps

Distributed Motionnet 2-ch Analog Output Module

• Dual channel +/- 10 V analog output
• RJ-45 communication port
• 2 way isolation on power, communication
• 16-bit high resolution, 0.3mV min
• Software calibration of offset/gain
• Rapid output rate, Slew rate = 20 V / us
• High precision, DNL = +/-1 LSB, INL = +/-3 LSB

Distributed Motionnet 32-ch Isolated DO Module

Distributed Motionnet 16-ch Isolated DI, 16-ch Isolated DO Module

Distributed Motionnet 32-ch Isolated DI Module

Distributed Motionnet Single-axis Universal Motion Control Module

Distributed Motionnet Four-axis Universal Motion Control Module with RJ-45 Connector. Includes 4x "CA-PC26M"

PCI Express Bus, Dual-line Motionnet Motion Control Module with RJ-45

PCI Express Bus, 6-axis Encoder Input Card

PCI Express Bus, 6-axis Encoder Input Card

• 6-axis encoder counter
• True 32-bit counter
• Encoder Counting Rate: 4 MHz (Max.)
• Third-order internal digital filter
• Counting Mode: Quadrant, CW/CCW, PULSE/DIR
• A+, A-, B+, B-, C+, C- inputs
• Programmable reset counter function
• Index (C channel) reset counter function
• Hardware reset (HR1 ~ HR6), reset counter function
• 68-pin SCSI-II connector

4-axis Stepper/Servo Motion Control Terminal Borad, for Universal Snap-on Wiring Purpose

3-axis Stepper/Servo Motion Control Terminal Borad, for Universal Snap-on Wiring Purpose

Serial Communication Remote Unit with High-speed 6-axis Motion Control Module

Serial Communication Remote Unit with High-speed 4-axis Motion Control Module

Ethernet Remote Unit with High-speed 6-axis Motion Control Module

Ethernet Remote Unit with High-speed 4-axis Motion Control Module

Ethernet Remote Unit with High-speed 4-axis Motion Control Module

• Remote control via Modbus TCP
• Can be controlled using SCADA, PAC, or PLC
• Can be integrated into a multi-station, multi-axis applications
• 4-axis motion control capability
• 2/3-axis linear interpolation function
• 2-axis circular interpolation function
• Programmable automatic homing function
• EzMove Utility for configuration and macro programming
• Test motion functions via EzMove without compilation
• Library for rapid development of applications
• Easy wiring for multi-station applications
• Can be set as a remote or stand-alone motion controller

PCI Bus, High-speed 8-axis Motion Control Card with FRnet Master

• Independent 8-axis motion control
• Support for hand wheel and jog functions
• 4-step home modes with auto-searching
• 2/3-axis linear interpolation function
• 2-axis circular interpolation function
• Programmable T/S-curve acceleration and deceleration
• Programmable ring counter
• Alarm reset and error counter clear output (ERC)
• High-speed auto-incremental and auto-reloadable compare output (CMP)
• Expandable remote I/O: 128 DI and 128 DO via a two-wire FRnet interface

PCI Express Bus, High-speed 4-axis Motion Control Card

• Independent 4-axis motion control
• Support for hand wheel and jog functions
• 2/3-axis linear / 2-axis circular interpolation function
• Continuous interpolation function
• Programmable T/S-curve acceleration and deceleration
• A maximum pulse output rate of 4 MHz for each axis
• Pulse output types: CW/CCW or PULSE/DIR
• 32-bit encoder counter for each axis
• Encoder pulse input types: A/B phase or Up/Down
• Programmable automatic homing for each axis
• Programmable software limits
• A wide range of synchronous actions (event-triggered actions)

Universal PCI Bus, High-speed 4-axis Motion Control Card with FRnet Master

• Independent 4-axis motion control Support for hand wheel and jog functions
• 2/3-axis linear / 2-axis circular interpolation function
• Continuous interpolation function
• Programmable T/S-curve acceleration and deceleration
• A maximum pulse output rate of 4 MHz for each axis
• Pulse output types: CW/CCW or PULSE/DIR
• 32-bit encoder counter for each axis
• Encoder pulse input types: A/B phase or Up/Down
• Programmable automatic homing for each axis
• Programmable software limits
• A wide range of synchronous actions (event-triggered actions)
• Expandable Remote I/O: 128 DI & 128 DO via a two-wire FRnet interface

PCI Bus, 3-axis Stepper Motor/Servo Control Card

• Universal PCI Bus
• 3-axis pulse command servo motor board
• Embedded CPU
• Max. Pulse Rate: 1 MHz
• 3-axis linear interpolation, circular interpolation
• Programmable trapezoidal speed profile
• Programmable DDA cycle
• Hardware emergency stop
• Drivers for DOS, Windows XP/2000 and Windows 7
• 8 DI, 7 DO channels

PCI Bus, High-speed 2-axis Motion Control Card with FRnet Master

• Independent 2-axis motion control
• Support for hand wheel and jog functions
• 2-axis linear / 2-axis circular interpolation function
• Continuous interpolation function
• Programmable T/S-curve acceleration and deceleration
• A maximum of 4 MHz pulse output rate for each axis
• Pulse output types: CW/CCW or PULSE/DIR
• 32-bit encoder counter for each axis
• Encoder pulse input types: A/B phase or Up/Down
• Programmable automatic homing for each axis
• Programmable software limits
• Expandable Remote I/O: 128 DI & 128 DO via a two-wire FRnet interface

2-port Modbus RTU/ASCII/TCP-to-BACnet/IP gateways

• Supports Modbus RTU/ASCII/TCP master/client
• Supports BACnet/IP slave/server
• Supports 600 points and 1200 points models
• Supports COV for fast data communication
• Supports virtual nodes designed to make each Modbus device as a separate BACnet/IP device
• Configures Modbus commands quickly by editing an Excel spreadsheet
• Embedded traffic and diagnostic information for easy troubleshooting
• Built-in Ethernet cascading for easy wiring
• Industrial design with -40 to 75°C operating temperature range
• Serial port with 2 kV isolation protection
• Dual AC/DC power supply
• Security features based on IEC 62443

1-port CAN-J1939 to Modbus/PROFINET/EtherNet/IP gateways

• Converts J1939 to Modbus, PROFINET, or EtherNet/IP
• Supports Modbus RTU/ASCII/TCP master/client and slave/server
• Supports EtherNet/IP Adapter Supports PROFINET IO device
• Supports J1939 protocol
• Effortless configuration via web-based wizard
• Built-in Ethernet cascading for easy wiring
• Embedded traffic monitoring/diagnostic information for easy troubleshooting
• microSD card for configuration backup/duplication and event logs
• Status monitoring and fault protection for easy maintenance
• CAN bus and serial port with 2 kV isolation protection
• -40 to 75°C wide operating temperature models available
• Security features based on IEC 62443

1-port PROFIBUS-to-PROFINET gateways

• Protocol conversion between PROFIBUS and PROFINET
• Supports PROFINET IO device
• Supports PROFIBUS DP V1 master
• Automatic scan of PROFIBUS devices and easy configuration
• Web-based GUI for I/O data visualization
• Built-in Ethernet cascading for easy wiring
• microSD card for configuration backup/duplication and event logs
• Embedded I/O monitoring and diagnostic information for easy troubleshooting
• Status monitoring and fault protection for easy maintenance
• Supports redundant dual DC power inputs and 1 relay output
• -40 to 75°C wide operating temperature models available
• Serial port with 2 kV isolation protection
• Security features based on IEC 62443

1-port Modbus RTU/ASCII/TCP/EtherNet/IP-to-PROFINET gateways

• Converts Modbus, or EtherNet/IP to PROFINET
• Supports PROFINET IO device
• Supports Modbus RTU/ASCII/TCP master/client and slave/server
• Supports EtherNet/IP Adapter
• Effortless configuration via web-based wizard
• Built-in Ethernet cascading for easy wiring
• Embedded traffic monitoring/diagnostic information for easy troubleshooting
• microSD card for configuration backup/duplication and event logs
• Status monitoring and fault protection for easy maintenance
• Serial port with 2 kV isolation protection -40 to 75°C wide operating temperature models available
• Supports redundant dual DC power inputs and 1 relay output
• Security features based on IEC 62443

Industrial PROFIBUS-to-fiber converters

• Fiber-cable test function validates fiber communication
• Auto baudrate detection and data speed of up to 12 Mbps
• PROFIBUS fail-safe prevents corrupted datagrams in functioning segments
• Fiber inverse feature
• Warnings and alerts by relay output
• 2 kV galvanic isolation protection
• Dual power inputs for redundancy (Reverse power protection)
• Extends PROFIBUS transmission distance up to 45 km
• Wide-temperature model available for -40 to 75°C environments
• Supports Fiber Signal Intensity Diagnosis

16-port managed Ethernet switches

• Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250 switches), and STP/RSTP/MSTP for network redundancy
• TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to enhance network security
• Easy network management by web browser, CLI, Telnet/serial console, Windows utility, and ABC-01
• Supports MXstudio for easy, visualized industrial network management

8-port entry-level managed Ethernet switches

• Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250 switches), and RSTP/STP for network redundancy
• IGMP Snooping, QoS, IEEE 802.1Q VLAN, and port-based VLAN supported
• Easy network management by web browser, CLI, Telnet/serial console, Windows utility, and ABC-01
• PROFINET or EtherNet/IP enabled by default (PN or EIP models)
• Supports MXstudio for easy, visualized industrial network management

8G-port full Gigabit unmanaged Ethernet switches

• Fiber-optic options for extending distance and improving electrical noise immunity
• Redundant dual 12/24/48 VDC power inputs
• Supports 9.6 KB jumbo frames
• Relay output warning for power failure and port break alarm
• Broadcast storm protection

5-port entry-level unmanaged Ethernet switches with metal housing

• 10/100BaseT(X) (RJ45 connector)
• Compact size for easy installation
• QoS supported to process critical data in heavy traffic
• IP40-rated metal housing

Quectel RM510Q-GL 5G M.2 Module

• Multi-Band 5G Sub-6 GHz & mmWave M.2 Module
• Max. downlink 4.5Gbps / 2.9Gbps uplink
• Extended temperature range of -40°C to +85°C

SIM8380G-M2 5G M.2 Module with mmWave

• Multi-Band 5G NR/LTE-FDD/LTE-TDD/HSPA+ module which supports R16 5G NSA/SA

SIM8280G-M2 5G M.2 Module

• Multi-Band 5G NR/LTE-FDD/LTE-TDD/HSPA+ module which supports R16 5G NSA/SA

PCIe x16 Single-port 100G QSFP+ Ethernet Network Adapter(E810)

• Intel master chip scheme
• PCI Express v4.0 x16
• iWARP and RoCEv2 Remote Direct Memory Access (RDMA)
• Intel Eth Adaptive Virtual Function
• Enhanced server virtualizations: 256 VFs, 768 VSIs
• IEEE 1588 Precision Time Protocol with per-packet time stamping

PCIe x4 Dual-port 10G PoE+ Ethernet Frame Grabber Card (Intel X550)

• Intel master chip scheme
• Mainly designed for industrial scene visual detection servers and equipment
• 30W PoE+ output, 4-Pin psu interface
• Adaptive to power output
• Heatsink & Fan for heat dissipation

Ethernet to fiber media converter, Single mode, SC-connector

• Wide input range DC power supply.
• Plug-and-Play design for the installation within seconds.
• Compact and Rugged Metal case capable of withstanding harsh environment.
• Data rate: 10/100Mbps auto-negotiation and half-/Full-duplex mode on TX port.
• Auto MDI-X/MDI-II for 10/100Base-TX port.
• Provides media conversion from UTP to Fiber Optic media types
• Supports link fault pass through function.
• Supports far end fault function.
• LED display to indicate the whole working status. 
• 3 power input types: Direct USB power, external DC adapter and screw terminal.
• Support IEEE Standard: 802.3u 100BaseTX & 100BaseFX

Dual-Port 100 Gb/s QSFP28 module with Intel® E810

• Supports multiple port speeds with a single architecture: 100/50/25/10/1GbE
• Intel® Ethernet Adaptive Virtual Function (Intel® Ethernet AVF)
• Enhanced server virtualization: 256 VFs, 768 VSIs
• Enhanced Data Plane Development Kit (DPDK)
• Suitable for data centers or cloud computing

• Support CANopen high layer protocol
• Support baud rate 100/125/250/500(default)/800/1000K
• Support CAN message acceptance filter
• Keep configuration after hardware reboot
• Up to 6000 CAN messages per second (receive data)
• Support Listen-only mode
• Additional driver to support Linux SocketCAN
• Termination resistor enabled/disabled by jumper
• Complies with EN61000-4-5 2.5kV Surge protection
• Complies with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Complies with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Supports 3^rd mounting hole and USB Pin header for out-of minicard installation
• Supports -40 to +85 degrees