IO-cards

Industrial M.2 (B+M key) PCIe USB Expansion Card

• Single-Line PCI-Express with throughput to 5.0/2.5 GT/s
• Fully compliant with PCI-Express Base Specification Rev.2.0
• Support simultaneous operation of multiple USB 1.1, USB 2.0, and USB 3.2 GEN1x1 devices
• Support individual USB devices running 5Gbps at full speed
• USB data transfer rate of 1.5/12/480/5000 Mbps 
• With Type-C cable

• Compliant with PCIe basic specification, v3.0 (compatible with PCIe v1.0 /1.1 & 2.0)
• Support PCle NVMe protocol
• Support RAID 0 ,RAID 1, JBOD
• Support 2230, 2242, 2260, 2280mm extended version SSD

mPCIe to Dual Isolated CAN FD Module

• Complies with IEC 60950-1 : 2005 + A1 : 2009 + A2 : 2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled / disabled by jumper
• Supports 3rd mounting hole and USB Pin header for out-of-minicard installation
  
  
• Baud rate up to 5 / 10 / 20 / 50 / 100 / 125 / 250 / 500(default) / 800 / 1000K
• CAN2.0 up to 7,800 frame/s (RX baud rate 1M, EID, 8byte data)
• CANFD up to 6,000 frame/s (RX baud rate 1M, data rate 5M, EID, 64byte data) 
• Data rate supports 2 / 4 / 5Mbps

M.2 2280 to Four Isolated CAN FD Module

• Complies with IEC 60950-1 : 2005 + A1 : 2009 + A2 : 2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled / disabled by jumper
• Additional driver to support Linux SocketCAN
• Complies with IEC 60950-1 : 2005 + A1 : 2009 + A2 : 2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled / disabled by jumper
• Additional driver to support Linux SocketCAN

M.2 2280 to Dual Isolated CAN FD Module

• Complies with IEC 60950-1 : 2005 + A1 : 2009 + A2 : 2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled / disabled by jumper
• Additional driver to support Linux SocketCAN
• Complies with IEC 60950-1 : 2005 + A1 : 2009 + A2 : 2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled / disabled by jumper
• Additional driver to support Linux SocketCAN

Industrial M.2 PCIe CAN Bus Expansion Card (-40℃~+85℃) 

• Single-Lane (x1) PCI-Express with throughput up to 5.0 / 2.5GT/s
• Fully compliant with PCI-Express Base Specification Rev. 2.0
• Meet the Requirements of the ISO 11898 High Speed Standard
• CAN bus 2.0B EFF backward compatible with 2.0A SFF
• Support baud rate 10/20/50/100/125/250/500/800/1000K
• Support CAN message acceptance filter
• Support 2.5kV isolated per port

mPCIe to dual isolated J1939/CANopen Module

• Compliant with ISO 11898-2
• Support baud rate 100/125/250/500(default)/800/1000K
• Support CAN message acceptance filter, listen-only mode
• Keep configuration after hardware reboot
• Up to 7,800 frame/s (receiving at 1Mbps, EID, 8byte data)
• Additional driver to support Linux SocketCAN
• Support SAE J1939/CANopen high layer protocol
• Termination resistor enabled/disabled by jumper
• Complies with EN61000-4-5 2.5kV Surge protection
• Complies with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Supports 3rd mounting hole and USB Pin header for out-ofminicard installation
• 30μ” golden finger, 3-year warranty
• Industrial Temperature (-40°C to +85°C) support

mPCIe to dual isolated CANbus 2.0B Module

• Compliant with ISO 11898-2
• Support baud rate 100/125/250/500(default)/800/1000K
• Support CAN message acceptance filter, listen-only mode
• Keep configuration after hardware reboot
• Up to 7,800 frame/s (receiving at 1Mbps, EID, 8byte data)
• Additional driver to support Linux SocketCAN
• Support SAE J1939/CANopen high layer protocol (Optional)
• Termination resistor enabled/disabled by jumper
• Complies with EN61000-4-5 2.5kV Surge protection
• Complies with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Supports 3rd mounting hole and USB Pin header for out-ofminicard installation
• 30μ” golden finger, 3-year warranty
• Industrial Temperature (-40°C to +85°C) support

PCIe x16 Dual-port 100G QSFP+ Ethernet Network Adapter(E810)

• Intel master chip scheme
• PCI Express v4.0 x16
• iWARP and RoCEv2 Remote Direct Memory Access (RDMA)
• Intel Ethernet Adaptive Virtual Function
• Enhanced server virtualizations: 256 VFs, 768 VSIs
• IEEE 1588 Precision Time Protocol with per-packet time stamping

PCIe x1 Single-port Gigabit SFP Ethernet Network Adapter  (Realtek RTL8111H Based)

Dual 10GbE Low Profile Ethernet Card (0℃~+55℃) with PoE+ Module, PCIex4

M.2 2280 dual isolated CAN bus 2.0B Board (-40℃~+85℃)

• CAN bus 2.0B backward compatible with 2.0A
• Compliant with ISO 11898
• Support baud rate 10/20/50/100/ 125/250/500/800/1000K
• Compliant with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Support Card ID and Silent mode setting by switch
• Support port to computer isolation 2.5kV
• Support CAN message acceptance filter

WLAN 802.11 a/b/g/n/ac 2T2R BT 4.2 M.2 Type 2230 key-A-E

Industrial I/O Control PCIe Card 16+16-ch Isolated Digital I/O

• Expands isolated eight (16) digital input channels with features for all channels.
  • Support both NPN & PNP devices
  • Support both dry and wet contact connections
  • With digital filter for noise reduction
  • Built-in 32-bit counter for all digital in channels
• Expands isolated eight (16) NPN type digital output channels with initial value (Booting & Restart) protection.
• Each channel built-in 2.5KV isolation protection for signal and power, allowing the input signals to be completely floated so as to prevent ground loops.
• Plug-n-Play, I/O address and IRQ assigned by system.
• Ultra low power consumption (<1.5W) design for green environment and industrial application.
• High quality electronic components, low impedance and high stability ensure product quality and reliability.

Industrial I/O Control PCIe Card 8+8-ch Isolated Digital I/O

• Expands isolated eight (8) digital input channels with features for all channels.
  • Support both NPN & PNP devices
  • Support both dry and wet contact connections
  • With digital filter for noise reduction
  • Built-in 32-bit counter for all digital in channels
• Expands isolated eight (8) NPN type digital output channels with initial value (Booting & Restart) protection.
• Each channel built-in 2.5KV isolation protection for signal and power, allowing the input signals to be completely floated so as to prevent ground loops
• Designed to meet PCI Express Base Specification Revision 2.1.
• With high reliable SUNIX QiuNiu UART Digital-I/O controller.
• Plug-n-Play, I/O address and IRQ assigned by system.

PCIe to 4-port Isolated CAN FD Communication Card

• Designed to meet PCI Express Base Specification Revision 2.1.
• Equipped with high reliable SUNIX QiuNiu controller.
• Complies with CAN specifications 2.0B and FD
• CAN FD bit rates for the data field up to 8 Mbit/s
• Isolation on the each CAN channel up to 2.5KV
• Surge protection up to 2KV
• Plug-n-Play, I/O address and IRQ assigned by system.
• Support proprietary SocketCAN driver, allowing users to program under Linux operating systems.

Industrial Mini PCIe to 2-port CAN FD Communication Card

• Suitable for mini PCIe slot based on PCI Express communication.
• Equipped with high reliable SUNIX QiuNiu controller.
• Complies with CAN specifications 2.0B and FD
• CAN FD bit rates for the data field up to 8 Mbit/s
• Plug-n-Play, I/O address and IRQ assigned by system.
• Support proprietary SocketCAN driver, allowing users to program under Linux operating systems.

PCIe to 2-port Isolated CAN FD Communication Card

• Designed to meet PCI Express Base Specification Revision 2.1.
• Equipped with high reliable SUNIX QiuNiu controller.
• Complies with CAN specifications 2.0B and FD
• CAN FD bit rates for the data field up to 8 Mbit/s
• Isolation on the each CAN channel up to 2.5KV
• Surge protection up to 2KV
• Plug-n-Play, I/O address and IRQ assigned by system.
• Support proprietary SocketCAN driver, allowing users to program under Linux operating systems.

Industrial M.2 to 2-port CAN FD Communication Card

• Suitable for M.2 slot with Key-M or Key-B based on PCI Express communication.
• Equipped with high reliable SUNIX QiuNiu controller.
• Complies with CAN specifications 2.0B and FD
• CAN FD bit rates for the data field up to 8 Mbit/s
• Plug-n-Play, I/O address and IRQ assigned by system.
• Support proprietary SocketCAN driver, allowing users to program under Linux operating systems.

PCIe x16 Single-port 100G QSFP+ Ethernet Network Adapter(E810)

• Intel master chip scheme
• PCI Express v4.0 x16
• iWARP and RoCEv2 Remote Direct Memory Access (RDMA)
• Intel Eth Adaptive Virtual Function
• Enhanced server virtualizations: 256 VFs, 768 VSIs
• IEEE 1588 Precision Time Protocol with per-packet time stamping

PCIe x4 Dual-port 10G PoE+ Ethernet Frame Grabber Card (Intel X550)

• Intel master chip scheme
• Mainly designed for industrial scene visual detection servers and equipment
• 30W PoE+ output, 4-Pin psu interface
• Adaptive to power output
• Heatsink & Fan for heat dissipation

• CANbus 2.0B backward compatible with 2.0A
• Support baud rate 100/125/250/500(default)/800/1000K
• Support CAN message acceptance filter
• Keep configuration after hardware reboot
• Up to 6000 CAN messages per second (receive data)
• Support Listen-only mode
• Additional driver to support Linux SocketCAN
• Termination resistor enabled/disabled by jumper
• Complies with EN61000-4-5 2.5kV Surge protection
• Complies with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Complies with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Supports 3^rd mounting hole and USB Pin header for out-of minicard installation
• Supports -40 to +85 degrees