Industrial communication

4G/5G/ Ethernet Gateway

• Cortex-A53 CPU, 1.6 GHz, quad-core
• 1 GB LPDDR4 RAM and 8 GB eMMC Flash
• Linux Kernel 4.14.98
• Provide NAT and port forwarding function
• Intelligent Remote Terminal Unit (RTU)
• Intelligent multiport serial gateway
• 4G / 5G wireless module (option)
• 64-bit Hardware Serial Number for Software Protection
• 10/100/1000M Two Ethernet Ports
• 4 Serial Ports (RS-232/485)

mPCIe to dual isolated J1939/CANopen Module

• Compliant with ISO 11898-2
• Support baud rate 100/125/250/500(default)/800/1000K
• Support CAN message acceptance filter, listen-only mode
• Keep configuration after hardware reboot
• Up to 7,800 frame/s (receiving at 1Mbps, EID, 8byte data)
• Additional driver to support Linux SocketCAN
• Support SAE J1939/CANopen high layer protocol
• Termination resistor enabled/disabled by jumper
• Complies with EN61000-4-5 2.5kV Surge protection
• Complies with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Supports 3rd mounting hole and USB Pin header for out-ofminicard installation
• 30μ” golden finger, 3-year warranty
• Industrial Temperature (-40°C to +85°C) support

8-port RS-232 USB-to-serial converters

• USB 3.2 SuperSpeed capability
• 512-byte on-chip FIFO cache and flow control for enhanced performance
• Drivers provided for a broad selection of operating systems, including Windows and Linux
• 50 bps to 921.6 kbps baudrate (nonstandard baudrates supported)
• Double-sided LEDs located at the corners show power, TX, and RX statuses in either directions
• Cascades with 3 UPort-G2 devices to up port capacity to 32 ports; no additional power adaptors required (UPort 1650-8-G2-Hub)
• Latching USB cable design for firmer connection
• Wide operating temperature models available for -40 to 75°C (-40 to 167°F) environments
• Serial port with 2 kV isolation protection (for “-I” models)

8-port RS-232/422/485 USB-to-serial converters

• USB 3.2 SuperSpeed capability
• 512-byte on-chip FIFO cache and flow control for enhanced performance
• Drivers provided for a broad selection of operating systems, including Windows and Linux
• 50 bps to 921.6 kbps baudrate (nonstandard baudrates supported)
• Double-sided LEDs located at the corners show power, TX, and RX statuses in either directions
• Cascades with 3 UPort-G2 devices to up port capacity to 32 ports; no additional power adaptors required (UPort 1650-8-G2-Hub)
• Latching USB cable design for firmer connection
• Wide operating temperature models available for -40 to 75°C (-40 to 167°F) environments
• Serial port with 2 kV isolation protection (for “-I” models)

4-port RS-232 USB-to-serial converters

• USB 3.2 SuperSpeed capability
• 512-byte on-chip FIFO cache and flow control for enhanced performance
• Drivers provided for a broad selection of operating systems, including Windows and Linux
• 50 bps to 921.6 kbps baudrate (nonstandard baudrates supported)
• Double-sided LEDs located at the corners show power, TX, and RX statuses in either directions
• Latching USB cable design for firmer connection
• Wide operating temperature models available for -40 to 75°C (-40 to 167°F) environments
• Serial port with 2 kV isolation protection (for “-I” models)

4-port RS-232/422/485 USB-to-serial converters

• USB 3.2 SuperSpeed capability
• 512-byte on-chip FIFO cache and flow control for enhanced performance
• Drivers provided for a broad selection of operating systems, including Windows and Linux
• 50 bps to 921.6 kbps baudrate (nonstandard baudrates supported)
• Double-sided LEDs located at the corners show power, TX, and RX statuses in either directions
• Latching USB cable design for firmer connection
• Wide operating temperature models available for -40 to 75°C (-40 to 167°F) environments
• Serial port with 2 kV isolation protection (for “-I” models)

2-port RS-232/422/485 USB-to-serial converters

• USB 3.2 SuperSpeed capability
• 50 bps to 921.6 kbps baudrate (nonstandard baudrates supported)
• 512-byte on-chip FIFO cache and flow control for enhanced performance
• Double-sided LEDs located at the corners show power, TX, and RX statuses in either directions
• Drivers provided for a broad selection of operating systems, including Windows and Linux
• Latching USB cable design for firmer connection
• Wide operating temperature models available for -40 to 75°C (-40 to 167°F) environments
• Serial port with 2 kV isolation protection (for “-I” models)

7 -port general-purpose USB 3.2 hub

• USB-IF certification
• USB 3.2 SuperSpeed capability
• Latching USB cable design for firmer connection
• Comprehensive diagnostic LEDs
• Dual power inputs (power jack and terminal block)
• DIN-rail housing and wall-mountable housing
• Rugged metal housing

4 -port general-purpose USB 3.2 hub

• USB-IF certification
• USB 3.2 SuperSpeed capability
• Latching USB cable design for firmer connection
• Comprehensive diagnostic LEDs
• Dual power inputs (power jack and terminal block)
• DIN-rail housing and wall-mountable housing
• Rugged metal housing

7 -port general-purpose USB 3.2 hub

• USB-IF certification
• USB 3.2 SuperSpeed capability
• IP30 aluminum housing
• DIN-rail housing and wall-mountable housing

4 -port general-purpose USB 3.2 hub

• USB-IF certification
• USB 3.2 SuperSpeed capability
• IP30 aluminum housing
• DIN-rail housing and wall-mountable housing

12G-port full Gigabit managed Ethernet switches with an 8 802.3bt PoE port option

• Developed according to the IEC 62443-4-1 and compliant with the IEC 62443-4-2 industrial cybersecurity standards
• Support for IEEE 802.3bt PoE for up to 90 W output per port
• Increased bandwidth capabilities with fiber SFP slots supporting up to 2.5 Gbps
• Turbo Ring and Turbo Chain (recovery time < 50 ms @ 250 switches), and RSTP/STP for network redundancy
• Wide range of power input options for flexible deployment
• Compact and flexible housing design to fit into confined spaces
• Supports MXstudio for easy, visualized industrial network management

8+4G-port managed Ethernet switches with an 8 802.3bt PoE port option

• Developed according to the IEC 62443-4-1 and compliant with the IEC 62443-4-2 industrial cybersecurity standards
• Support for IEEE 802.3bt PoE for up to 90 W output per port
• Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250 switches) , and RSTP/STP for network redundancy
• Wide range of power input options for flexible deployment
• Compact and flexible housing design to fit into confined spaces
• Supports MXstudio for easy, visualized industrial network management

8-port managed Ethernet switches with options of 4 802.3bt PoE ports or 4 Gigabit uplink ports

• Developed according to the IEC 62443-4-1 and compliant with the IEC 62443-4-2 industrial cybersecurity standards
• Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250 switches) , and RSTP/STP for network redundancy
• Support for IEEE 802.3bt PoE for up to 90 W output per port
• Wide range of power input options for flexible deployment
• Compact and flexible housing design to fit into confined spaces
• Supports MXstudio for easy, visualized industrial network management

mPCIe to dual isolated CANbus 2.0B Module

• Compliant with ISO 11898-2
• Support baud rate 100/125/250/500(default)/800/1000K
• Support CAN message acceptance filter, listen-only mode
• Keep configuration after hardware reboot
• Up to 7,800 frame/s (receiving at 1Mbps, EID, 8byte data)
• Additional driver to support Linux SocketCAN
• Support SAE J1939/CANopen high layer protocol (Optional)
• Termination resistor enabled/disabled by jumper
• Complies with EN61000-4-5 2.5kV Surge protection
• Complies with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Supports 3rd mounting hole and USB Pin header for out-ofminicard installation
• 30μ” golden finger, 3-year warranty
• Industrial Temperature (-40°C to +85°C) support

8SSR Relay/8 DI Intelligent I/O Gateway

• Linux open platform
• 8-channel SSR relay/ 8-channel digital input
• Programming: Linux C API, Node-RED (graphic programming environment)
• Cloud / database access, edge data analysis and logic control, and data visualization by dashboard 
• Interfaces: RS-485x2, Ethernet port x 2 ,1 x USB Type-A 2.0, 1 x USB Micro-B 2.0

EMEA/LATAM/APAC, 2x Ethernet, Wi-Fi, Metal, Without Accessories

• LTE cat.4, 3G/HSPA+, GPRS/EDGE, EMEA, 2x SIM
• LTE B1, B3, B7, B8, B20
• DIN and Wall mount options
• 2x ETH
• WiFi - 802.11n, AP, Multi SSID, WDS
• Operating temp. –30 °C to +70 °C, Power input : 5-18VDC (DC Jack), accessory with EU type power adapter
• Certifications: CE
• Diagnostics, VPN support, Firewall, WAN failover

8-ch Relay and 8-ch Isolated Digital Input w/ digital filter and interrupt PCIe Card

• 8 opto-isolated digital input channels
• 8 relay actuator output channels
• Interrupt handling capability for all DI channels
• Selectable Digital filter time for all DI channels
• Output status readable
• LED indicator to show activated relays

16-ch Relay and 16-ch Isolated Digital Input w/ digital filter & interrupt PCIe Card

• 16-ch digital input and 16-ch relay
• Interrupt handling capability for all DI channels
• Selectable Digital filter time for all DI channels
• Output status readable
• LED indicator to show activated relays
• Selectable Form A or Form B

32-ch Isolated Digital I/O with universal output PCIE Card

• 16-ch isolated digital input
• 16-ch isolated digital output for both PNP(source)/ NPN (sink) type
• High output driving capacity
• DO type selectable by software
• High isolation voltage (2,500 VDC

128-ch Isolated Digital I/O PCIE Card

• Interrupt handling capability for each channel
• 128 isolated digital output channels (64 channels for PCI-1758UDIO)
• High-voltage isolation on output channels (2,500 VDC)
• Wide output range (5 ~ 40 VDC)
• High-sink current for isolated output channels (90 mA max./channel)
• BoardID™ switch
• Digital output value retained after hot system reset
• PCIE-1758DI and PCIE-1758DIO
• 128 isolated digital input channels (64 channels for PCI-1758UDIO)
• Wide input range (10 ~ 30 VDC)
• High ESD protection (2,000 VDC)
• Digital Filter function

10/30 MS/s, 12-bit, 4-ch Simultaneous Analog Input PCI Card

• 4 single-ended analog input channels
• 12-bit A/D converter, with up to 30 MHz sampling rate
• Multiple A/D triggering modes
• Onboard FIFO memory 32,768 samples
• 4 A/D converters simultaneously sampling
• Programmable gain
• Programmable pacer/counter
• BoardID™ switch
• Universal PCI Bus (supports 3.3 V or 5 V PCI bus signals)

100 kS/s, 12-bit, 32-ch Isolated Analog Input Universal PCI Card

• 2,500 VDC isolation protection
• 32-ch single-ended or 16-ch differential or a combination of analog input
• 12-bit resolution for A/D conversion
• Programmable gain for each input channel
• Software, internal or external pacer sampling modes supported
• Onboard FIFO memory: 4,096 samples;
• Universal PCI bus
• BoardID™ switch

16/8-ch, 18-bit, 1MS/s/ch Simultaneous Analog Input PCI Express DAQ Card

• 16/8-ch simultaneous sampling up to 1 MS/s
• 18-bit resolution
• Software selectable low-pass filter
• Wide input range up to 40 Vpp (±20 V range)
• Support both voltage and current measurement
• Multiple selectable trigger modes

125/80 MS/S, 16-bit, 4-ch Simultaneous Digitizer

• 4 simultaneous analog inputs, up to 125MHz, 16-bit resolution
• 500MHz Time Interleaved Sampling
• Non-stop data streaming capable
• 2 GB on-board memory
• 1M or 50 Ohm selectable input impedance
• On-Board tunable anti-aliasing filter
• AC/DC Coupling

216 kS/s, 24-bit, 8/4-ch PCIE Card for Sound and Vibration

• 24-bit resolution ADCs with 115 dB dynamic range
• Wide input ranges from ±0.2 V to ±10 V
• Software selectable AC/DC coupling
• Software configurable 4 or 10 mA Integrated Electronic Piezoelectric Excitation (IEPE)
• Built-in anti-aliasing filter
• 8 simultaneously sampled analog inputs up to 216 kS/s
• Multiple card synchronization
• Full auto-calibration

128 kS/s, 24-bit, 8-ch PCIE Card for Sound and Vibration

• 8 simultaneously sampled analog inputs, up to 128 kS/s
• 24-bit resolution ADCs with -102 dB total harmonic distortion plus noise (THD+N)

1MS/s, 16-bit, 32-ch Analog Input PCIE Card

• 32-ch single-ended or 16-ch differential or a combination of analog input
• 16-bit A/D converter, with up to 1MHz sampling rate
• Multi-card synchronization
• Current measurement (0-20mA or 4-20mA)
• Support digital and analog triggers
• Auto calibration

1 MS/s, 16-bit, 16-ch Universal Multifunction PCI Card

• 16-ch single-ended or 8-ch differential analog input
• 16-bit A/D converter, with up to 1 MHz sampling rate
• Onboard FIFO memory (1,024 samples)
• 16-ch digital input and 16-ch digital output
• 2 x 16-bit analog output channels
• Auto calibration
• Universal PCI bus (support 3.3 V or 5 V PCI bus signal)
• Onboard programmable counter
• BoardID™ switch

100 kS/s, 12-bit, 16-ch Universal Multifunction PCI Card

• One 12-bit analog output channel
• 16-ch single-ended or 8-ch differential analog input
• 12-bit A/D converter, with up to 100 kHz sampling rate
• 16-ch digital input and 16-ch digital output
• Automatic channel/gain scanning
• Onboard FIFO memory (1,024 samples)
• ISA-Compatible with PCL-818HD
• Programmable gain
• Universal PCI bus (support 3.3 V or 5 V PCI bus signal)
• BoardID™ switch

500kS/s, 16-bit, 16-ch Multifunction PCI Card

• 16 single-ended or 8 differential or a combination of analog inputs
• 16-bit A/D converter, with up to 500 kHz sampling rate
• FIFO memory (8,192 samples)
• 2 analog output channels
• 16-ch digital input and 16-ch digital output
• Auto-calibration
• BoardID™ switch

1 MS/s, 12-bit, 16-ch Multifunction PCI Card

• 16 single-ended or 8 differential or a combination of analog inputs
• 12-bit A/D converter, with up to 1 MHz sampling rate
• Two 12-bit analog output channels with continuous waveform output function
• 16-ch digital input and 16-ch digital output
• Three 16-bit programmable multifunction counter/timers on 10 MHz
• Programmable gain
• Automatic channel/gain scanning
• Onboard FIFO memory (AI: 1,024 samples AO: 32,768 samples)
• Auto-calibration (AI/AO)
• PCI-Bus for data transfer
• Pre-, post-, about- and delay-trigger data acquisition modes for analog input channels
• Flexible triggering and clocking capabilities

100 kS/s, 12-bit, 16-ch Universal Multifunction PCI Card

• 16-ch single-ended or 8-ch differential or a combination of analog input
• 12-bit A/D converter, with up to 100 kHz sampling rate
• Onboard programmable counter
• Two 12-bit analog output channels
• 16-ch digital input and 16-ch digital output
• Automatic channel/gain scanning
• Onboard FIFO memory (4,096 samples)
• Programmable gain
• BoardID™ switch

5 MS/s, 16-bit, 16-ch Multifunction PCIE Card

• 16 analog inputs, up to 5 MS/s, 16-bit resolution
• 2 analog outputs up to 3 MS/s, 16-bit resolution
• Support Analog and Digital Trigger for AI/O
• Support Waveform generation for AO
• 24 programmable digital I/O lines
• Two 32-bit programmable counter/timers
• Onboard FIFO memory (8k samples)
• Support for Microsoft Windows 7/10 and Linux

250 kS/s, 16-bit, 8-ch, Simultaneous Sampling, Multifunction PCIE Card

• 8 differential simultaneous sampling analog inputs, up to 250 kS/s, 16-bit resolution
• 2 analog outputs, up to 3 MS/s, 16-bit resolution
• Full auto-calibration
• 2 analog triggers and 2 digital triggers for AI/O
• 32 programmable DI/Os with interrupt functions
• Four 32-bit programmable counters/ timers/ encoders
• Board ID switch
• Support for Microsoft Windows 10, 8 and 7