Industrial communication

10/30 MS/s, 12-bit, 4-ch Simultaneous Analog Input PCI Card

• 4 single-ended analog input channels
• 12-bit A/D converter, with up to 30 MHz sampling rate
• Multiple A/D triggering modes
• Onboard FIFO memory 32,768 samples
• 4 A/D converters simultaneously sampling
• Programmable gain
• Programmable pacer/counter
• BoardID™ switch
• Universal PCI Bus (supports 3.3 V or 5 V PCI bus signals)

100 kS/s, 12-bit, 32-ch Isolated Analog Input Universal PCI Card

• 2,500 VDC isolation protection
• 32-ch single-ended or 16-ch differential or a combination of analog input
• 12-bit resolution for A/D conversion
• Programmable gain for each input channel
• Software, internal or external pacer sampling modes supported
• Onboard FIFO memory: 4,096 samples;
• Universal PCI bus
• BoardID™ switch

16/8-ch, 18-bit, 1MS/s/ch Simultaneous Analog Input PCI Express DAQ Card

• 16/8-ch simultaneous sampling up to 1 MS/s
• 18-bit resolution
• Software selectable low-pass filter
• Wide input range up to 40 Vpp (±20 V range)
• Support both voltage and current measurement
• Multiple selectable trigger modes

125/80 MS/S, 16-bit, 4-ch Simultaneous Digitizer

• 4 simultaneous analog inputs, up to 125MHz, 16-bit resolution
• 500MHz Time Interleaved Sampling
• Non-stop data streaming capable
• 2 GB on-board memory
• 1M or 50 Ohm selectable input impedance
• On-Board tunable anti-aliasing filter
• AC/DC Coupling

216 kS/s, 24-bit, 8/4-ch PCIE Card for Sound and Vibration

• 24-bit resolution ADCs with 115 dB dynamic range
• Wide input ranges from ±0.2 V to ±10 V
• Software selectable AC/DC coupling
• Software configurable 4 or 10 mA Integrated Electronic Piezoelectric Excitation (IEPE)
• Built-in anti-aliasing filter
• 8 simultaneously sampled analog inputs up to 216 kS/s
• Multiple card synchronization
• Full auto-calibration

128 kS/s, 24-bit, 8-ch PCIE Card for Sound and Vibration

• 8 simultaneously sampled analog inputs, up to 128 kS/s
• 24-bit resolution ADCs with -102 dB total harmonic distortion plus noise (THD+N)

1MS/s, 16-bit, 32-ch Analog Input PCIE Card

• 32-ch single-ended or 16-ch differential or a combination of analog input
• 16-bit A/D converter, with up to 1MHz sampling rate
• Multi-card synchronization
• Current measurement (0-20mA or 4-20mA)
• Support digital and analog triggers
• Auto calibration

1 MS/s, 16-bit, 16-ch Universal Multifunction PCI Card

• 16-ch single-ended or 8-ch differential analog input
• 16-bit A/D converter, with up to 1 MHz sampling rate
• Onboard FIFO memory (1,024 samples)
• 16-ch digital input and 16-ch digital output
• 2 x 16-bit analog output channels
• Auto calibration
• Universal PCI bus (support 3.3 V or 5 V PCI bus signal)
• Onboard programmable counter
• BoardID™ switch

100 kS/s, 12-bit, 16-ch Universal Multifunction PCI Card

• One 12-bit analog output channel
• 16-ch single-ended or 8-ch differential analog input
• 12-bit A/D converter, with up to 100 kHz sampling rate
• 16-ch digital input and 16-ch digital output
• Automatic channel/gain scanning
• Onboard FIFO memory (1,024 samples)
• ISA-Compatible with PCL-818HD
• Programmable gain
• Universal PCI bus (support 3.3 V or 5 V PCI bus signal)
• BoardID™ switch

500kS/s, 16-bit, 16-ch Multifunction PCI Card

• 16 single-ended or 8 differential or a combination of analog inputs
• 16-bit A/D converter, with up to 500 kHz sampling rate
• FIFO memory (8,192 samples)
• 2 analog output channels
• 16-ch digital input and 16-ch digital output
• Auto-calibration
• BoardID™ switch

1 MS/s, 12-bit, 16-ch Multifunction PCI Card

• 16 single-ended or 8 differential or a combination of analog inputs
• 12-bit A/D converter, with up to 1 MHz sampling rate
• Two 12-bit analog output channels with continuous waveform output function
• 16-ch digital input and 16-ch digital output
• Three 16-bit programmable multifunction counter/timers on 10 MHz
• Programmable gain
• Automatic channel/gain scanning
• Onboard FIFO memory (AI: 1,024 samples AO: 32,768 samples)
• Auto-calibration (AI/AO)
• PCI-Bus for data transfer
• Pre-, post-, about- and delay-trigger data acquisition modes for analog input channels
• Flexible triggering and clocking capabilities

100 kS/s, 12-bit, 16-ch Universal Multifunction PCI Card

• 16-ch single-ended or 8-ch differential or a combination of analog input
• 12-bit A/D converter, with up to 100 kHz sampling rate
• Onboard programmable counter
• Two 12-bit analog output channels
• 16-ch digital input and 16-ch digital output
• Automatic channel/gain scanning
• Onboard FIFO memory (4,096 samples)
• Programmable gain
• BoardID™ switch

5 MS/s, 16-bit, 16-ch Multifunction PCIE Card

• 16 analog inputs, up to 5 MS/s, 16-bit resolution
• 2 analog outputs up to 3 MS/s, 16-bit resolution
• Support Analog and Digital Trigger for AI/O
• Support Waveform generation for AO
• 24 programmable digital I/O lines
• Two 32-bit programmable counter/timers
• Onboard FIFO memory (8k samples)
• Support for Microsoft Windows 7/10 and Linux

250 kS/s, 16-bit, 8-ch, Simultaneous Sampling, Multifunction PCIE Card

• 8 differential simultaneous sampling analog inputs, up to 250 kS/s, 16-bit resolution
• 2 analog outputs, up to 3 MS/s, 16-bit resolution
• Full auto-calibration
• 2 analog triggers and 2 digital triggers for AI/O
• 32 programmable DI/Os with interrupt functions
• Four 32-bit programmable counters/ timers/ encoders
• Board ID switch
• Support for Microsoft Windows 10, 8 and 7

38.4 kS/s, 26-bit, 4-Ch, Simultaneous Sampling, Universal Bridge Input, Multifunction PCI Express Card

• 4 simultaneous sampling analog inputs, up to 38.4 kS/s, 26-bit resolution
• Full, half, and quarter-bridge sensor input with built-in anti-aliasing filter
• 2 analog outputs, up to 3 MS/s, 16-bit resolution
• Four 32-bit programmable encoder counters/ timers/ encoder counters
• 32 programmable DI/Os with interrupt functions
• Board ID switch
• Full automatic calibration

8-slot USB 3.0 iDAQ Base Unit

• USB 3.0 SuperSpeed
• Wide range power input
• LED status indicators
• Physical ID switch for multiple module identification
• 8 iDAQ slots
• 2 programmable function pin for timing signal (trigger, clock) input/output

8-ch, 16-bit, 1MS/s/ch Analog Input iDAQ Module

• 8-ch simultaneous sampling up to 1 MS/s
• 16-bit resolution
• Software selectable low-pass filter
• Wide input range up to 40 Vpp (±20 V range)
• Support both voltage and current measurement

200kS/s, 16-bit, 8-ch Analog Input iDAQ Module

• Hot-swappable in iDAQ system
• Detachable Euro-type spring terminal connectors
• 8 x 16-bit analog input channels with 600VRMS isolation
• Supports voltage and current measurements
• Wide common-mode voltage range (±275 V)

256kS/s/ch, 24-bit, 4-ch iDAQ Module for Sound and Vibration

• Hot-swappable in iDAQ system
• 4-ch simultaneous sampling up to 256kS/s
• 24-bit resolution
• Direct IEPE supply
• Anti-aliasing filter equipped
• High gain up to ±187.5mV input range

48-ch TTL DI/O iDAQ Module

• Hot-swappable in iDAQ system
• Detachable Euro-type spring terminal connectors
• 48-channel TTL digital I/Os
• Configurable digital I/O direction
• Isolation protection of 60 VDC
• Supports buffered acquisition/update rates up to 200kHz

16-ch Isolated DI, 16-ch Isolated DO iDAQ Module

• Hot-swappable in iDAQ system
• Euro-type spring terminal blocks
• 32-ch isolated DI/O (16-ch digital input, 16-ch digital output)
• High output driving capacity
• Interrupt handling capability
• Digital output type changeable between sink (NPN) type and source (NPN) type
• Isolation protection of 600 VRMS
• Support buffered acquisition/update rate up to 10kHz

4-Slot USB 3.0 iDAQ Base Unit

• Built-in USB 3.0 SuperSpeed hub
• Wide-range power input
• LED status indicators
• Physical ID switch for multiple module identification
• 4 x iDAQ slots
• 2 x programmable function pins for timing signals (trigger, clock) input/output

16-ch Isolated Digital Input and 16-ch Relay USB 3.0 I/O Module

• USB 3.0 SuperSpeed
• Daisy chainable by built in USB hub
• 16-ch Isolated Digital Input and 16-ch Form A-type Relay Output
• Wide input voltage range (10 ~ 30 VDC)
• High-voltage isolation on input channel (2,500 VDC )
• Quick removable European type connector
• LED indicators for I/O status
• Supported operating systems: Windows XP/7/8/10

32-ch Isolated DI and 32-ch Isolated DO USB 3.0 I/O Module

• USB 3.0 SuperSpeed
• Daisy chainable by built in USB hub
• 32-ch digital input and 32-ch digital output with 2,500 VDC isolation
• Wide input voltage range (10 ~ 30 VDC)
• Wide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)
• Quick removable European type connector
• LED indicators for I/O status
• Supported operating systems: Windows XP/7/8/10

32-ch Isolated Digital Input and 16-ch PhotoMOS Relay USB 3.0 I/O Module

• USB 3.0 SuperSpeed
• Daisy chainable by built in USB hub
• 32-ch digital input and 16-ch PhotoMOS Relay output (Form A) isolation
• Wide input voltage range (10 ~ 30 VDC)
• 1500 VDC optical isolation for relay outputs
• Quick removable European type connector
• LED indicators for I/O status
• Supported operating systems: Windows XP/7/8/10

8-ch Isolated Digital Input and 8-ch Relay USB 3.0 I/O Module

• USB 3.0 SuperSpeed
• Daisy chainable by built in USB hub
• 8-ch Isolated Digital Input and 8-ch Form A-type Relay Output
• Wide input voltage range (10 ~ 30 VDC)
• High-voltage isolation on input channel (2,500 VDC )
• Quick removable European type connector
• LED indicators for I/O status
• Supported operating systems: Windows XP/7/8/10

16-ch Isolated Digital Input and 8-ch PhotoMOS Relay USB 3.0 I/O Module

• USB 3.0 SuperSpeed
• Daisy chainable by built in USB hub
• 16-ch digital input and 8-ch PhotoMOS Relay output (Form A) isolation
• Wide input voltage range (10 ~ 30 VDC)
• 1500 VDC optical isolation for relay outputs
• Quick removable European type connector
• LED indicators for I/O status
• Supported operating systems: Windows XP/7/8/10

16-ch Isolated DI and 16-ch Isolated DO USB 3.0 I/O Module

• USB 3.0 SuperSpeed
• Daisy chainable by built in USB hub
• 16-ch digital input and 16-ch digital output with 2,500 VDC isolation
• Wide input voltage range (10 ~ 30 VDC)
• Wide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)
• Quick removable European type connector
• LED indicators for I/O status
• Supported operating systems: Windows XP/7/8/10

8-ch, 16-bit, 200 kS/s Isolated Analog Input USB 3.0 I/O Module

• USB 3.0 SuperSpeed
• Daisy chainable by built-in USB hub
• 8 x 16-bit analog input channels with 2,500 VDC isolation
• Support voltage and current measurement
• Wide common-mode voltage range (±275 V)
• Removable European-type connector
• Supported operating systems: Windows XP/7/8/10

4-ch, 16-bit, 200 kS/s Isolated Analog Output USB 3.0 I/O Module

• USB 3.0 SuperSpeed
• Daisy chainable by built-in USB hub
• 4 x 16-bit analog output channels with 2,500 V DC isolation
• Multiple voltage and current output ranges
• Removable European-type connector
• Supported operating systems: Windows XP/7/8/10

PCIe x16 Dual-port 100G QSFP+ Ethernet Network Adapter(E810)

• Intel master chip scheme
• PCI Express v4.0 x16
• iWARP and RoCEv2 Remote Direct Memory Access (RDMA)
• Intel Ethernet Adaptive Virtual Function
• Enhanced server virtualizations: 256 VFs, 768 VSIs
• IEEE 1588 Precision Time Protocol with per-packet time stamping

Intel® Ethernet Controller XL710-BM1 based Network Interface Card with 4 x SFP+ by 1 PCIe 3.0 x 8 interface

• 1 x Intel® Ethernet Controller XL710-BM1
• 4 ports 10 GbE SFP+ connector
• PCIe 3.0 x8

Intel® Ethernet Controller EZE810CAM2 based Network Interface Card with 2 x QSFP28 by 1 PCIe 4.0 x8 interface

• 1 x Intel E810 Ethernet controller
• 2 ports 100GbE QSFP28 connector
• 1 x PCIe 4.0 x8

OCP3.0 Quad-port Gigabit Ethernet Network Adapter (Intel I350)

OCP3.0 Dual-port 100G QSFP28 Ethernet Network Adapter (Intel E810)

OCP 3.0 Quad-port Mezzanine 10G SFP+ Ethernet Network Adapter (Intel XL710)

OCP 3.0 Dual-port 10G SFP+ Ethernet Network Adapter (Intel X710)

IEC61850-3 20G SFP + 6GE Managed Ethernet Switch, 48DC

• -40 ~ 85˚C wide-range operating temperature
• Dual Power input and 2 relay output
• Redundancy: Gigabit X-Ring Pro (ultra high-speed recovery time < 20 ms), RSTP/STP (802.1w/1D),MSTP
• Security: 802.1x (Port-Based, MD5/TLS/TTLS/PEAP Encryption), HTTPS, SSH and SNMPv3
• Management: SNMP v1/v2c/v3, WEB, Telnet, Standard MIB
• SFP socket for Easy and Flexible Fiber Expansion
• 20 x Gigabit SFP ports + 6 x Gigabit x RJ-45 ports

• Entry-level managed switch
• Provides wide operating voltage 8.4~52.8 VDC
• C1D2 and ATEX certified for horizontal area
• IXM function enables fast deployment
• Modbus/TCP enabled by default
• Supports X-Ring for ultra high-speed recovery time less than 20m

• 16 ports Fast Ethernet RJ-45 (EKI-5526/I-PN)
• Entry-Level Managed Switch
• IXM function enables fast deployment
• Provides GSDML files
• Management: SNMP v1/v2c/v3, WEB, Standard MIB, Private MIB
• Supports Media Redundancy Protocol (Media Redundancy Client)