Motion Solutions

PCI Bus, Dual-line Motionnet Master Card with Terminal Block

• Maximum Communication Speed: 20 Mbps
• Distributed motion control up to 128 axes
• Distributed I/O points up to 4096 points
• Parallel I/O Ports: 8 Input and 4 Output channels
• Optional quadrature encoder input for linear scale or manual pulse generator input

PCI Bus, Dual-line Motionnet Master Card with RJ-45 Connector

Distributed Motionnet Single-axis Motion Control Module with e-CON Mini-Clamp connector for Delta ASDA-A/A2

• Maximum communication speed: 20 Mbps
• Pulse Output Rate: 6.6 MHz (Max.)
• Control up to 64 axes per line
• Multi-axis linear interpolation function
• 2-axis circular interpolation function
• T/S-curve acceleration and deceleration
• Change speed and position on the fly
• Slow down sensor, home sensor, positive and negative limit sensors for each axis
• Software limit and compare trigger output
• Three-way isolation for power, communication and I/O.(Provide better noise immunity and device protection)
• The EC module equipped with Mini-Clamp connector provide for an easier and debris-free wire termination process

Distributed Motionnet Single-axis Motion Control Module with e-CON Mini-Clamp connector for Yaskawa Sigma II/III/V

Distributed Motionnet Single-axis Motion Control Module with e-CON Mini-Clamp connector for Panasonic MINAS A4

Distributed Motionnet Single-axis Motion Control Module with e-CON Mini-Clamp connector for Mitsubishi MELSERVO-J3/J4

• Maximum communication speed: 20 Mbps
• Pulse Output Rate: 6.6 MHz (Max.)
• Control up to 64 axes per line
• Multi-axis linear interpolation function
• 2-axis circular interpolation function
• T/S-curve acceleration and deceleration
• Change speed and position on the fly
• Slow down sensor, home sensor, positive and negative limit sensors for each axis
• Software limit and compare trigger output
• Three-way isolation for power, communication and I/O.(Provide better noise immunity and device protection)
• The EC module equipped with Mini-Clamp connector provide for an easier and debris-free wire termination process

Distributed Motionnet 8-ch Analog Input Module

• 8 +/- 10 V analog input
• RJ-45 communication port
• 2 way isolation on power, communication
• 16-bit high resolution, 0.3mV min
• High precision and low shift reference 5V inside
• Hardware offset, gain calibration to EEPROM storage
• Rapid A/D transformation. Sampling rate = 250 ksps

Distributed Motionnet 2-ch Analog Output Module

• Dual channel +/- 10 V analog output
• RJ-45 communication port
• 2 way isolation on power, communication
• 16-bit high resolution, 0.3mV min
• Software calibration of offset/gain
• Rapid output rate, Slew rate = 20 V / us
• High precision, DNL = +/-1 LSB, INL = +/-3 LSB

Distributed Motionnet 32-ch Isolated DO Module

Distributed Motionnet 16-ch Isolated DI, 16-ch Isolated DO Module

Distributed Motionnet 32-ch Isolated DI Module

Distributed Motionnet Single-axis Universal Motion Control Module

Distributed Motionnet Four-axis Universal Motion Control Module with RJ-45 Connector. Includes 4x "CA-PC26M"

PCI Express Bus, Dual-line Motionnet Motion Control Module with RJ-45

PCI Express Bus, 6-axis Encoder Input Card

PCI Express Bus, 6-axis Encoder Input Card

• 6-axis encoder counter
• True 32-bit counter
• Encoder Counting Rate: 4 MHz (Max.)
• Third-order internal digital filter
• Counting Mode: Quadrant, CW/CCW, PULSE/DIR
• A+, A-, B+, B-, C+, C- inputs
• Programmable reset counter function
• Index (C channel) reset counter function
• Hardware reset (HR1 ~ HR6), reset counter function
• 68-pin SCSI-II connector

4-axis Stepper/Servo Motion Control Terminal Borad, for Universal Snap-on Wiring Purpose

3-axis Stepper/Servo Motion Control Terminal Borad, for Universal Snap-on Wiring Purpose

Serial Communication Remote Unit with High-speed 6-axis Motion Control Module

Serial Communication Remote Unit with High-speed 4-axis Motion Control Module

Ethernet Remote Unit with High-speed 6-axis Motion Control Module

Ethernet Remote Unit with High-speed 4-axis Motion Control Module

Ethernet Remote Unit with High-speed 4-axis Motion Control Module

• Remote control via Modbus TCP
• Can be controlled using SCADA, PAC, or PLC
• Can be integrated into a multi-station, multi-axis applications
• 4-axis motion control capability
• 2/3-axis linear interpolation function
• 2-axis circular interpolation function
• Programmable automatic homing function
• EzMove Utility for configuration and macro programming
• Test motion functions via EzMove without compilation
• Library for rapid development of applications
• Easy wiring for multi-station applications
• Can be set as a remote or stand-alone motion controller

PCI Bus, High-speed 8-axis Motion Control Card with FRnet Master

• Independent 8-axis motion control
• Support for hand wheel and jog functions
• 4-step home modes with auto-searching
• 2/3-axis linear interpolation function
• 2-axis circular interpolation function
• Programmable T/S-curve acceleration and deceleration
• Programmable ring counter
• Alarm reset and error counter clear output (ERC)
• High-speed auto-incremental and auto-reloadable compare output (CMP)
• Expandable remote I/O: 128 DI and 128 DO via a two-wire FRnet interface

PCI Express Bus, High-speed 4-axis Motion Control Card

• Independent 4-axis motion control
• Support for hand wheel and jog functions
• 2/3-axis linear / 2-axis circular interpolation function
• Continuous interpolation function
• Programmable T/S-curve acceleration and deceleration
• A maximum pulse output rate of 4 MHz for each axis
• Pulse output types: CW/CCW or PULSE/DIR
• 32-bit encoder counter for each axis
• Encoder pulse input types: A/B phase or Up/Down
• Programmable automatic homing for each axis
• Programmable software limits
• A wide range of synchronous actions (event-triggered actions)

Universal PCI Bus, High-speed 4-axis Motion Control Card with FRnet Master

• Independent 4-axis motion control Support for hand wheel and jog functions
• 2/3-axis linear / 2-axis circular interpolation function
• Continuous interpolation function
• Programmable T/S-curve acceleration and deceleration
• A maximum pulse output rate of 4 MHz for each axis
• Pulse output types: CW/CCW or PULSE/DIR
• 32-bit encoder counter for each axis
• Encoder pulse input types: A/B phase or Up/Down
• Programmable automatic homing for each axis
• Programmable software limits
• A wide range of synchronous actions (event-triggered actions)
• Expandable Remote I/O: 128 DI & 128 DO via a two-wire FRnet interface

PCI Bus, 3-axis Stepper Motor/Servo Control Card

• Universal PCI Bus
• 3-axis pulse command servo motor board
• Embedded CPU
• Max. Pulse Rate: 1 MHz
• 3-axis linear interpolation, circular interpolation
• Programmable trapezoidal speed profile
• Programmable DDA cycle
• Hardware emergency stop
• Drivers for DOS, Windows XP/2000 and Windows 7
• 8 DI, 7 DO channels

PCI Bus, High-speed 2-axis Motion Control Card with FRnet Master

• Independent 2-axis motion control
• Support for hand wheel and jog functions
• 2-axis linear / 2-axis circular interpolation function
• Continuous interpolation function
• Programmable T/S-curve acceleration and deceleration
• A maximum of 4 MHz pulse output rate for each axis
• Pulse output types: CW/CCW or PULSE/DIR
• 32-bit encoder counter for each axis
• Encoder pulse input types: A/B phase or Up/Down
• Programmable automatic homing for each axis
• Programmable software limits
• Expandable Remote I/O: 128 DI & 128 DO via a two-wire FRnet interface