Ohjainkortit

Industrial Multi-GNSS (GPS, GLONASS, BeiDou, Galileo, QZSS and SBAS) module with M.2 2242 B Key form factor

• M.2 2242 Key B form factor
• 92 channel support u-blox NEO-M9N engine (GPS, GLONASS, BeiDou, Galileo, QZSS andSBAS)
• Open sky cold start 24 second / Aided starts 2 second
• USB 2.0 communication interface
• Accuracy 1.5m CEP
• Operating temperature: -40°C ~ +85°C

Industrial Multi-GNSS (GPS, GLONASS, BeiDou, Galileo, QZSS and SBAS) module with half size mini-PCIe form factor

• 92 Channels u-blox NEO-M9 engine (GPS, GLONASS, BeiDou, Galileo, QZSS and SBAS)
• Untethered Dead Reckoning(UDR)
• Including IMU and Oscillator
• 2 second TTFF for Hot Starts, Open sky code start 24 second.
• Accuracy SBAS 1.5M CEP
• Operating temperature: -40 to +85° C

Wi-fi 6 enterprise Access Point mPCIe card

• 192-bit WPA3 enterprise encryption
• Hotspot 2.0 and Wi-Fi Direct
• Renesas Celeno, CL8040 chipset
• Support up to 128 clients

Digital I/O Board with isolation

• Contact rating: DC 80V / 50mA max
• Isolation Protection: 3750Vrms

32 GPIO extension card, mpcie

WLAN 802.11 a/b/g/n/ac 2T2R BT 4.0 mPCIe

WLAN 802.11 a/b/g/n/ac/ax 2T2R BT 5.2 M.2 Type 2230 key-A-E

10G Dual port Ethernet adapter, PCIEx8,  Intel X550

10G Single port Ethernet adapter, PCIEx4,  AQC107

mPCIe to dual isolated CANbus 2.0B

• Compliant with PCI Express 1.1
• Meet the Requirements of the ISO 11898-1
• CAN bus 2.0B backward compatible with 2.0A
• Support baud rate 10/20/50/100/250/500/800/1000K
• Support CAN message acceptance filter
• Support Linux SocketCAN
• Compliant with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Compliant with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled/disabled by jumper
• 30μ” golden finger, 3-year warranty
• Industrial Temperature (-40°C to +85°C) suppor

mPCIe Single Port Gigabit SFP Ethernet Adapter (1x SFP)

• Single-port 1000MBASE-X controller with integrated MAC and PHY
• Four transmit quest and four receive queues per port
• 1000Mbps Fiber Ethernet networks transition

PCIe x4 Quad-port PoE+ Gigabit Vision Frame Grabber Card (Intel I210)

• Intel master chip scheme
• Mainly designed for industrial scene visual detection servers and equipment
• 30W PoE+ output, 4-Pin psu interface
• Adaptive to power output
• Large heatsink for heat dissipation

M.2 2242 to single isolated CAN bus Module

• Compliant with PCI Express 1.1
• Meet the Requirements of the ISO 11898-1
• CAN bus 2.0B backward compatible with 2.0A
• Support baud rate 10/20/50/100/250/500/800/1000K
• Support CAN message acceptance filter
• Support Linux SocketCAN
• Compliant with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Compliant with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled/disabled by switch
• Industrial Temperature (-40°C to +85°C) support

• Support CANopen high layer protocol
• Support baud rate 100/125/250/500(default)/800/1000K
• Support CAN message acceptance filter
• Keep configuration after hardware reboot
• Up to 6000 CAN messages per second (receive data)
• Support Listen-only mode
• Additional driver to support Linux SocketCAN
• Termination resistor enabled/disabled by jumper
• Complies with EN61000-4-5 2.5kV Surge protection
• Complies with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Complies with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Supports 3^rd mounting hole and USB Pin header for out-of minicard installation
• Supports -40 to +85 degrees

PCI- e low profile 8 port USB3.2 board

• Quad-Lane (x4) PCI-Express with throughput up to 5.0/2.5GT/s
• 8-port USB 3.2 PCI Express Card with 4 independent host controllers
• 900 mA/1500 mA max. per port configurable via switch settings
• Support Hot-Swap function
• Support individual four USB devices running 5Gbps at full speed
• Support simultaneous operation of multiple USB 1.1, USB 2.0, and USB 3.2 GEN1x1 devices
• USB data transfer rate of 1.5/ 12/ 480/ 5000 Mbps
• With Type-C cable

PCI- e low profile 8 port USB3.2 board

• Quad-Lane (x4) PCI-Express with throughput up to 5.0/2.5GT/s
• 8-port USB 3.2 PCI Express Card with 4 independent host controllers
• 900 mA/1500 mA max. per port configurable via switch settings
• Support Hot-Swap function
• Support individual four USB devices running 5Gbps at full speed
• Support simultaneous operation of multiple USB 1.1, USB 2.0, and USB 3.2 GEN1x1 devices
• USB data transfer rate of 1.5/ 12/ 480/ 5000 Mbps

PCI- e low profile 8 port USB3.2 board

• Quad-Lane (x4) PCI-Express with throughput up to 5.0/2.5GT/s
• 4-port USB 3.2 PCI Express Card with 4 independent host controllers
• 900 mA/1500 mA max. per port configurable via switch settings
• Support Hot-Swap function
• Support individual four USB devices running 5Gbps at full speed
• Support simultaneous operation of multiple USB 1.1, USB 2.0, and USB 3.2 GEN1x1 devices
• USB data transfer rate of 1.5/ 12/ 480/ 5000 Mbps

PCIe x4 Quad-port PoE+ 2.5GbE Vision Frame Grabber Card (Intel I226 based)

• Intel master chip scheme
• Mainly designed for industrial scene visual detection servers and equipment
• 30W PoE+ output, 4-Pin psu interface
• Adaptive to power output
• Large heatsink for heat dissipation

M.2 2242 to single isolated CAN bus Module

• Compliant with PCI Express 1.1
• Meet the Requirements of the ISO 11898-1
• CAN bus 2.0B backward compatible with 2.0A
• Support baud rate 10/20/50/100/250/500/800/1000K
• Support CAN message acceptance filter
• Support Linux SocketCAN
• Compliant with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Compliant with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled/disabled by switch
• Industrial Temperature (-40°C to +85°C) support

PCI Express, 200 kS/s, 16-ch, 16-bit Simultaneously Sampled AI Board with 12-ch Isolated DI

M.2 2280 to four isolated CANbus 2.0B module

• Compliant with PCI Express 1.1
• Meet the Requirements of the ISO 11898-1
• CAN bus 2.0B backward compatible with 2.0A
• Support baud rate 10/20/50/100/250/500/800/1000K
• Support CAN message acceptance filter
• Support Linux SocketCAN
• Support SAE J1939/CANopen high layer protocol (Optional)
• Compliant with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Compliant with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled/disabled by switch
• 30μ” golden finger, 3-year warranty
• Industrial Temperature (-40°C to +85°C) support

M.2 2280 to dual isolated CAN bus Module

• Compliant with PCI Express 1.1
• Meet the Requirements of the ISO 11898-1
• CAN bus 2.0B backward compatible with 2.0A
• Support baud rate 10/20/50/100/250/500/800/1000K
• Support CAN message acceptance filter
• Support Linux SocketCAN
• Support SAE J1939/CANopen high layer protocol (Optional)
• Compliant with IEC 60950-1:2005 + A1: 2009 + A2:2013 2.5kV HiPOT protection
• Compliant with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled/disabled by switch
• 30μ” golden finger, 3-year warranty
• Industrial Temperature (-40°C to +85°C) support

Wi-fi 7 enterprise Access Point mPCIe card

• Qualcomm QCN9274 chipset
• Dual diplexer setup enables 2x2+2x2 data streams on the 2.4 and 5 GHz bands concurrently with only 2 antennas

1-Port EtherCAT I/O MainDevice mPCIe Card

• Meets Advantech iDoor technology standard
• PCI ExpressR Mini card specification revision 1.2 compliant
• Identical interface for all EtherCAT Motion Cotrollers
• Support high speed IO control in EtherCAT
• Connect I/O SubordinateDevice automatically without ESI/ENI
• Easy-to-use EtherCAT integrated development environment
• Provide error detection and diagnostics to monitor the entire EtherCAT network

M.2 2242 (USB HS) to Single Isolated CAN FD

• Baud rate up to 5 / 10 / 20 / 50 / 100 / 125 / 250 / 500 (default) / 800 / 1000K
• Data rate up to 2 / 4 / 5Mbps (For more details, refer to *Notes in the specification table below)
• CAN 2.0 up to 7,800 frame/s (RX baud rate 1M, EID, 8byte data)
• CAN FD up to 6,000 frame/s (RX baud rate 1M, data rate 5M, EID, 64byte data)

PCIe to Four Isolated CAN FD Module

• Baud rate up to 5 / 10 / 20 / 50 / 100 / 125 / 250 / 500 (default) / 800 / 1000K
• CAN2.0 up to 7,800 frame/s (RX baud rate 1M, EID, 8byte data)
• CANFD up to 6,000 frame/s (RX baud rate 1M, data rate 5M, EID, 64byte data) 
• Data rate supports 2 / 4 / 5Mbps
• Complies with IEC 60950-1 : 2005 + A1 : 2009 + A2 : 2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled / disabled by jumper
• Optional M.2 slot to expand 2 ~ 4 more CAN ports by installing EGUC series

PCIe to Dual Isolated CAN FD Module

• Baud rate up to 5 / 10 / 20 / 50 / 100 / 125 / 250 / 500 (default) / 800 / 1000K
• CAN2.0 up to 7,800 frame/s (RX baud rate 1M, EID, 8byte data)
• CANFD up to 6,000 frame/s (RX baud rate 1M, data rate 5M, EID, 64byte data) 
• Data rate supports 2 / 4 / 5Mbps
• Complies with IEC 60950-1 : 2005 + A1 : 2009 + A2 : 2013 2.5kV HiPOT protection
• Complaint with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
• Termination resistor enabled / disabled by jumper
• Optional M.2 slot to expand 2 ~ 4 more CAN ports by installing EGUC series

M.2 2280 2 port USB 3.2 board with Type-C cable

• Dual-Lane (x2) PCI-Express with throughput to 5.0/2.5 GT/s
• Fully compliant with PCI-Express Base Specification Rev.2.0
• Support simultaneous operation of multiple USB 1.1, USB 2.0, and USB 3.2 GEN1x1 devices
• Support individual two USB devices running 5Gbps at full speed
• USB data transfer rate of 1.5/12/480/5000 Mbps 
• With Type-C cable

Industrial M.2 (B+M key) PCIe USB Expansion Card

• Single-Line PCI-Express with throughput to 5.0/2.5 GT/s
• Fully compliant with PCI-Express Base Specification Rev.2.0
• Support simultaneous operation of multiple USB 1.1, USB 2.0, and USB 3.2 GEN1x1 devices
• Support individual USB devices running 5Gbps at full speed
• USB data transfer rate of 1.5/12/480/5000 Mbps 
• With Type-C cable

• Compliant with PCIe basic specification, v3.0 (compatible with PCIe v1.0 /1.1 & 2.0)
• Support PCle NVMe protocol
• Support RAID 0 ,RAID 1, JBOD
• Support 2230, 2242, 2260, 2280mm extended version SSD